Apron flashing
Apron flashing where a roof slope meets a wall above is renewed with proper laps over the shingles.
Roof Repair
Flashing Repair Leonia, NJ
A Leonia roofer can stop leaks where the roof meets a wall, dormer, skylight or edge by renewing the flashing at that joint, woven correctly with the shingles and tucked behind the siding. One call to (551) 348-8956 reaches a nearby roofer who repairs flashing.
Flashing is the thin metal that seals every place the roof surface is interrupted. Step flashing is a series of small bent pieces woven in with each course of shingles along a sidewall, counter flashing laps over it from the wall side, a kickout at the bottom of the wall throws water into the gutter, and drip edge lines the eaves and rakes. When any piece is missing, loose or rusted through, water gets behind the roof covering.
Flashing leaks are sneaky because the water often runs into the wall instead of the attic. A missing kickout is a classic example: water running down the roof edge pours behind the siding at the bottom of the wall, and the rot shows up later as soft trim, stained siding or a damp window below. By the time it is visible, the repair may include some siding and wall sheathing too.
A bead of sealant along a joint is a warning sign, not a repair. Sealant smeared where flashing should be dries and cracks in a few seasons, and it can trap water instead of shedding it. Proper flashing sheds water by gravity and lapping, so it keeps working even after any sealant ages.
Many flashing repair calls in Leonia also turn up a need for chimney flashing repair or roof leak repair.
Dealing with this in Leonia, NJ right now? Call (551) 348-8956 to talk to a local roofer.
Call nowThe process
The flashing repair process
Flashing repair is a layering job, done from the bottom up.
Find the failure
The roofer checks the joint from the roof and the attic, looking for missing pieces, rust, face nails and caulk hiding a gap. Probing the wall below shows whether water has reached the sheathing.
Open the joint
The shingles next to the wall come up, and the lowest siding courses come off to expose the flashing. New flashing has to tuck behind the housewrap, which means opening the wall a little.
Weave in the metal
Each new step piece overlaps the one beneath it, and the kickout at the base sends water into the gutter. Fasteners go into the roof deck only, never through the vertical leg into the wall.
Add counter flashing
On masonry walls, counter flashing is set into a cut joint; on framed walls, the housewrap and siding cover the flashing. The gap lets the joint dry and keeps trim from wicking water.
Seal the eaves
Damaged drip edge is renewed so water drips clear of the fascia. Correct laps at the edges keep water out of the fascia and soffit.
What is included
Flashing a roofer can repair
Edge flashing
Edge metal is renewed along the roof perimeter to protect the deck edge.
Kickout flashing
A kickout is added where a roof edge ends against a wall which protects the wall below.
Cap flashing
Loose counter flashing is secured where the wall and roof meet.
Step flashing
Step pieces along walls and dormer cheeks are replaced so water stays on the roof.
Related service
Roof Flashing Repair Leonia, NJ
Roof flashing repair ranges from resetting a single loose piece to rebuilding a full sidewall. Some repairs take an hour at one corner; others mean opening a whole wall joint and replacing the metal course by course. Knowing the scope up front avoids surprises once siding comes off.
Material matters too. Copper, galvanized steel and aluminum all show up on roofs, and each has spots where it works best. Matching metals avoids corrosion where new and old flashing meet.
Related service
Roof Valley Flashing Leonia, NJ
A valley is where two roof slopes meet, and it channels a large share of the roof water toward the eave. Valleys are either open, with exposed metal, or closed, with shingles running through them. Both need ice and water shield underneath, centered in the valley.
Common valley problems include rusted metal, debris dams, worn shingles and nails placed too close to the centerline. Small installation details, like clipping the upper corners of the cut shingles, keep water flowing down the valley instead of across it. Fixing a valley usually involves stripping it, relining it and installing new metal or reshingling.
Local help
Flashing Repair Near Me
Flashing repairs in Leonia are common on houses with dormers, additions and second-story walls rising above lower roofs. From Leonia out to neighboring towns such as Palisades Park, Fort Lee, Ridgefield Park and Englewood, older homes often have rusted or face-nailed flashing, while newer ones sometimes lack kickouts entirely, and each of those joints is a place worth checking.
Searching for flashing repair near me from Leonia or Palisades Park, Fort Lee, Ridgefield Park and Englewood? Call (551) 348-8956 to talk to a roofer who works in your part of town.
Roofs in this climate
Winters here are long and cold, with snow on the roof for weeks at a time and plenty of nights below freezing. When warm attic air melts the snow, the meltwater runs down and freezes again at the eaves, building ice dams that push water up under the shingles. Strong coastal storms push rain into every weak spot at the flashing and valleys. That is why roof repair in Leonia is busiest after a hard winter and before the next one.
Why call
Why fix it now
Smaller repairs
A roof problem fixed early rarely spreads to the decking, the insulation or the ceilings.
Local knowledge
Local roofers see the same roofs and storm damage across Leonia and nearby towns.
Straight answers
Ask your questions before you agree to anything.
Common questions about flashing repair
Is it possible to fix flashing without a new roof?
Flashing is repaired on existing roofs all the time. The roofer removes the shingles and siding along the joint, installs new flashing and reshingles that strip. For a worn-out roof, combining the work with a replacement avoids doing the joint twice.
What are the signs of bad roof flashing?
Look for stains or drips that line up with a roof-to-wall joint. Outside, look for rust, gaps, lifted metal, nails through the face and heavy caulk along the joint. Soft or stained siding at the bottom of a sidewall often means a missing kickout. A roofer reached at (551) 348-8956 can look at every joint.
What is step flashing and why does it matter?
Step flashing uses individual bent pieces that interleave with each shingle course. Because each piece laps the one below, water is passed down the wall joint from piece to piece and onto the roof. A long single strip sends water under the roofing, which is why step pieces are the standard.
Will caulk fix leaking flashing?
A bead of caulk may hold for a season or two, but it will fail. Sun and temperature swings crack it, and water gets behind it again, sometimes trapped where it rots wood faster. A proper repair replaces the metal so it sheds water without depending on sealant.
What is a kickout flashing?
It is a bent piece of flashing at the lower end of a sidewall joint. It throws runoff away from the wall and into the gutter. Leaving it out is one of the most common causes of rot in the wall under a roof edge.
More questions? Call (551) 348-8956
Related services
Chimney Flashing Repair
Fixing leaks around the chimney with new flashing set into the mortar joints, instead of another coat of tar.
Learn moreRoof Leak Repair
Stopping water at the pipe boots, flashing, valleys and nail holes where roofs actually leak, with the damage underneath checked too.
Learn moreSkylight Repair
Repairs for skylight leaks, failed glass seals and worn flashing kits, without replacing a unit that can still be saved.
Learn moreRoof Vent Repair
Fixing the vents and pipe collars that poke through a roof and often leak first, with the attic airflow kept working.
Learn more
Looking for something else?
See all roofing servicesNeed flashing repair in Leonia, NJ?
Call now for Leonia flashing repair and help in the towns around it.