Flashing
Walls, curbs, pipes and edges are flashed for a finished roof.
Flat Roofing
Rubber Roof Installation Leonia, NJ
A roofer in Leonia can install a rubber roof by laying EPDM membrane in wide sheets over insulation and a cover board, bonding or fastening it down and sealing every seam with primer and tape, with as few seams as possible. Dial (551) 348-8956 to talk with a local roofer about a new rubber roof.
A true rubber roof is EPDM, a synthetic rubber membrane used on flat and low slope roofs for decades. EPDM is sold in wide rolls, typically 45 or 60 mil thick, and it stretches and recovers as the roof moves through hot and cold seasons. That flexibility is why it suits so many homes.
Attachment method shapes the rest of the installation. Adhered, fastened and ballasted systems each suit different buildings and wind conditions. For homes, adhered EPDM is the most common choice.
Two more decisions round out the plan. A 60 mil sheet is tougher than 45 mil for roofs that see foot traffic. White EPDM suits sunny roofs, and black suits cooler climates. The transition to a steeper roof or a wall is planned with the same care, since that is where low roofs most often leak.
Depending on what the roofer finds, rubber roof installation in Leonia, NJ can go hand in hand with rubber roof repair and flat roof installation.
Looking for Leonia rubber roof installation? Call (551) 348-8956 to talk to a local roofer.
Call nowThe process
The rubber roof installation process
A rubber roof is built in layers, with the seams and flashing as the critical details.
Prepare the deck
The roofer checks the deck for rot, gaps and loose sheets and confirms the roof has enough slope to drain. A tear-off comes first on existing roofs.
Install insulation
Insulation boards go down for energy savings and slope, topped by a smooth cover board. Tapered boards add slope where needed.
Sheet layout
The membrane is unrolled, aligned and allowed to settle before bonding. Seams are planned so they run with the slope.
Bond the membrane
Bonding adhesive is rolled onto both the cover board and the underside of the rubber, then the sheet is folded back down and broomed smooth. The process repeats for the second half. Air pockets left under the sheet can turn into blisters later, so the crew works the rubber flat from the center out.
Seaming
Primer and seam tape join the sheets, with T-joints covered by extra patches. Exposed edges get lap sealant.
Finish the edges
Perimeter edge metal, wall flashing and pipe boots complete the roof. Termination bar and counter flashing seal the wall edge. Before the crew leaves, seams are probed for any loose spots.
What is included
What goes into a rubber roof
Seam tape
Laps are joined with seam tape and is checked before closeout.
Insulation
Insulation adds energy savings and slope under the rubber.
Deck preparation
Old roofing is removed and the deck is repaired for a sound start.
Rubber sheet
A 45 or 60 mil EPDM sheet is installed with as few seams as possible.
Related service
EPDM Roof Installation Leonia, NJ
Installing EPDM well comes down to preparation, seams and flashing. Rushing the adhesive, skipping primer or leaving wrinkles under the sheet are the common mistakes. Dry, mild days give the best bond. Different adhesives may be used in the field and at the flashings, each matched to the job it does.
For a Leonia home, the installer thinks ahead to how the roof will behave over the years. Flashing at walls and curbs is secured with termination bar so the sheet cannot pull loose as it ages, and corners get flexible uncured flashing. It is worth asking how the edges will be secured.
Local help
Rubber Roof Installation Near Me
Rubber roofs in Leonia are common on porches, garages, additions and flat sections of older homes. Across Leonia and nearby towns like Palisades Park, Fort Lee, Ridgefield Park and Englewood, EPDM handles storms, sun and cold well when it is installed with good seams and drainage, and the right installer makes a big difference.
For rubber roof installation in Leonia, NJ or nearby towns like Palisades Park, Fort Lee, Ridgefield Park and Englewood, call (551) 348-8956 to reach a roofer who covers your street.
How the weather here affects roofs around Leonia
Cold winters bring snow, ice and a long stretch of freezing nights. When warm attic air melts the snow, the meltwater runs down and freezes again at the eaves, building ice dams that push water up under the shingles. Coastal storms and heavy spring rain drive water sideways into flashing, valleys and old chimneys. Most homeowners in Leonia, NJ have the roof checked in the fall and again after the snow melts.
Why call
Why act early
Smaller repairs
Small roof problems caught early usually stay small repairs.
Familiar with local homes
Local roofers see the same roofs and storm damage across Leonia and nearby towns.
Clear next steps
Ask your questions before you agree to anything.
Common questions about rubber roof installation
How thick should a rubber roof be?
The common choices are 45 mil and 60 mil. The thicker sheet holds up better to traffic and weather. Heavy duty options exist too.
What is the difference between EPDM and TPO?
EPDM is synthetic rubber, while TPO is a thermoplastic membrane. Black EPDM is taped and stretchy, and white TPO is welded and reflective. Both are common on flat roofs.
Is it possible to install EPDM over the old roof?
EPDM can sometimes go over an existing roof. There should be only one existing layer, the insulation must be dry and a cover board or recover board goes between the old roof and the rubber. Otherwise, a tear-off is needed. A moisture check of the old roof settles the question before any work is planned.
What is the lifespan of a new EPDM roof?
Rubber roofs often last decades. Thickness, seam quality and maintenance all affect its life. Repairs are simple when needed.
Should my rubber roof be black or white?
The choice depends on the climate and the space below. White helps in sunny climates, and black is common where winters are long. A roofer can recommend what fits your home.
More questions? Call (551) 348-8956
Other services that may help
Rubber Roof Repair
EPDM rubber roof repairs done with primer, cover tape and lap sealant made for rubber, never with tar or asphalt cement that ruins the rubber.
Learn moreFlat Roof Installation
Installing TPO, PVC, EPDM or modified bitumen roofs on additions, garages, porches and flat-roof homes, planned around how the roof will be used.
Learn moreTPO Roofing
Heat-welded TPO membrane for flat and low-slope roofs, built around proper drainage, flashing and edge metal.
Learn moreFlat Roof Replacement
Replacing old built-up, torch-down, EPDM or TPO roofs with a new system built to drain, and new flashing at every wall, curb and drain.
Learn more
Looking for something else?
See all roofing servicesTalk to a Leonia roofer about rubber roof installation
Call (551) 348-8956 for a local roofer in Leonia and nearby towns.